Audio Interface Setup For Webrtc

Category view

Audio Interface Setup for WebRTC
Published on Dec 30, 2024

Article summary
Scope
This article serves as a how-to guide for setting up a source using WebRTC with a Telos
Alliance Axia Altus Virtual Broadcast Console.
Description
This article is meant to help remote users connect with our WebRTC remote monitoring and
contribution solutions. This guide references third-party products and should be used
according to their instructions. If you experience difficulty getting the installation to work, we
are happy to confirm your Altus setup; however, you may need to contact the other company
for further assistance.
Why WebRTC?
Leveraging WebRTC technology enables real-time media communications directly between
browsers and devices, essentially allowing talent at a remote location to connect to the mixer
all they need is an Internet connection and an HTML5-enabled web browser.
The delay in the headphone back-feed is one of the challenges that talent experience when
performing remote mixing, due in large part to the latency from the Internet sending a back-
feed with the voice included this also creates listening difficulty.  
Thankfully, on the Pro Audio side, there are many options available in the marketplace that
allow users to level the remote audio experience without breaking the budget. Let s take an
in-depth look at four options we have tested successfully, these third-party devices enable
users to monitor the local microphone (sidetone) right out of the box.
Options 1 & 2: All-In-One
This is a preferred option for a simple-setup as only two connections required to make this
work; one to the computer for power and audio transfer (typically via USB) and another for

headphone monitoring via a 3.5mm connection. These solutions have a microphone built-in
and it can be plug-and-play. The downside to this solution is there is not an easy way to
connect monitor speakers in addition to local headphones.
1. Elgato Wave 3: Link -> https://www.elgato.com/en/wave-3
a. Elgato Wave XLR: this one lets you choose your microphone, it acts more like a
traditional interface without studio monitor connections. Link ->
https://www.elgato.com/en/wave-xlr
2. Shure MV7: Link -> https://www.shure.com/en-US/products/microphones/mv7
As previously stated, there are other options available; however, the options discussed here
have been tested in the field. The Elgato Wave 3 and Shure MV7 are equipped with settings
for mic gain, headphone volume, and monitoring crossfade built into the microphone;
therefore, no other windows audio settings are required for operation. While these
microphones are compatible with their own software that allows for even more capability, we
encourage you to seek their product information directly for more information.
Option 3 & 4 : Audio Interface + Mic
The approach described below is still a great option and allows more flexibility because you
can select your favorite microphone. The concept is the same – the mic goes into the interface
via XLR, headphones can be used and most interfaces have a direct monitor. This solution
also has the ability to connect studio monitors to use in addition to headphones.
1. Focusrite Solo: Link -> https://focusrite.com/en/audio-interface/scarlett/scarlett-solo
2. Audient EVO 4 USB Audio Interface: Link -> https://evo.audio/products/evo-4/overview/
While we covered four field-tested options as of this writing, there are many others available
due to the broad range of similar products in the category. Please feel free to let us know if
you have found success with additional options.
Let us know how we can help
If you have further questions on this topic or have ideas about improving this document,
please contact us.

Documento adaptado por Ing. Sebastián Vallejos

Atm Rack Ears

Category view

ATM Rack Ears
Published on Dec 11, 2024

Article summary
Scope
This document pertains to the 25-Seven Automated Time Manager.
2001-00348-000 Audio Time Manager – AES
2001-00349-000 Audio Time Manager – LIVEWIRE
The Rack Ears

If you're in need of a replacement rack ear, contact Customer Support and ask for pricing and
availability of part # 1451-00788-101.
The same rack ear is interchangeable between both sides of the ATM, meaning you can order
two of the same ear if you need a set of rack ears.
Other ATM Parts
The ATM has been out of production for quite some time and parts are becoming harder and
harder to find. If you're in need of a power supply, CPU board or button caps, contact Support
and we will do our best to accommodate your needs.
Let us know how we can help
Each ear needs four 6-32 x 1/4" Phillips flat screws. These can be picked up at your
local hardware store or ordered using part # 1301-00232-100.

If you have further questions on this topic or have ideas about improving this document,
please contact us.

Documento adaptado por Ing. Sebastián Vallejos

Atm Audio Time Manager

Category view
ATM (Audio Time Manager)
1 Sub categories
Help Documents
2 Articles

Documento adaptado por Ing. Sebastián Vallejos

Arc Television Loudness Processor

Category view
ARC Television Loudness Processor
1 Sub categories
2 Articles
Linear Acoustic ARC Television Loudness Processor
Published on Nov 5, 2024
A budget-friendly, easy-to-use, 2-channel television processor specifically designed for regions and applications
that do not require support for multi-channel, coded audio. The Linear Acoustic ARC is a budget-friendly, easy-to-
use, 2-channel telev…
Quick Start Guide
Published on Nov 5, 2024
V0.0.64 and V1.2 Firmware Hardware Overview ARC Front Panel Figure 1 – Front panel ARC front panel features
include: Four status LEDs indicating the status of each power supply (1A, 1B), the overall status of the unit (1C),
and sy…
User Manual V0.0.64
1 Sub categories
6 Articles
Published on Nov 5, 2024
Linear Acoustic ARC

Documento adaptado por Ing. Sebastián Vallejos

Ap 3000 Quick Start Guide

Category view

AP-3000 Quick Start Guide
Published on Dec 16, 2024

Article summary
AP-3000 Front Panel
AP-3000 Rear Panel
Thank you for Purchasing the AP-3000
AP-3000 hosts pre-installed container-delivered Telos Alliance products, providing an
alternative to customers who want the benefits of our software-based products but prefer
not to purchase and configure their own server for hosting.
Mounting the Included External Power Supply
The AP-3000 is rack-mountable using the two included rack ears and a two-part power
adapter shelf bracket.
1. Secure the rack ears to the chassis using the three provided screws on each side. The
rack ear with the Telos Alliance logo is intended to be installed on the left side of the AP-
3000.
2. To install the power adapter bracket, first clip the power adapter into place on the
bracket as shown in the illustration below, then add the retention bracket using the two
provided screws.
3. Mount the power adapter bracket assembly on the right side of the chassis using the
three provided screws.

AP-3000 Connections
The AP-3000 uses an external power supply. Connect the output of the power supply to the
AP-3000 s threaded DC input (B), then connect AC power to the power supply s IEC input
(A).
NIC 1 (C) connects the AP-3000 to your AoIP network, and NIC 2 (D) is used for the
WAN/internet connection (if configured for dual network use). For detailed network
information, please see your AP-3000 configuration sheet.

Container Configuration
Each container will have its own web interface, accessible through its unique IP address.
Please see your AP-3000 configuration sheet for additional information on how to access
your containers
Portainer
AP-3000 also includes Portainer, a web-based configuration and management tool for each
individual container installed on the platform. Accessing Portainer may be necessary to apply
software updates or to change an IP address.
To reach Portainer, open a web browser and navigate to the IP address of one of the AP-
3000 s physical NICs at port 9000 (for example, 192.168.2.100:9000). When accessing
Portainer for the first time, you will be prompted to create a new password. After doing so,
log in with the default username admin and your newly created password.
Additional Support
If you need additional help or support with AP-3000, please contact us directly or summit a
Support Ticket by clicking on Request Support at the top of this page.
NOTE: The USB, HDMI, and Display Port connections are not necessary for normal use,
and should only be used if instructed by Telos Alliance support.
Logging in to Portainer provides access to all of the installed containers, including the
ability to start, stop, restart, and remove individual containers. Removing a container
will delete its settings, and a new container must be created from scratch. Do not
remove any containers unless instructed to do so by Telos Alliance support.

Documento adaptado por Ing. Sebastián Vallejos

Ap 3000 Password Reset

Category view

AP-3000 Password Reset
Published on Mar 20, 2025

Article summary
Scope
This document explains how to reset the CLI user account on an AP-3000.
Prerequisites
An imaging tool like Etcher
A 2 GB or larger USB flash drive that can be overwritten
Physical access to the AP-3000
Keyboard and Monitor with HDMI or Display Port
How to reset the password
1. Download the password reset utility, below
2. Plug the USB drive into the computer
3. Open Etcher
4. Select the Flash from file option
5. Select the password reset utility from the menu
6. Click Select Target
7. Select the USB drive that you want to use
8. Click the Flash! button
9. When flashing is complete, eject the USB drive
10. Plug the USB Drive into the AP-3000, along with a keyboard and monitor.
11. Reboot the AP-3000
12. As the AP-3000 boots, press DEL on the keyboard until the Setup Menu appears
13. Use the arrow keys to select highlight the Boot tab
14. Arrow down to Boot Option 2. Press the Enter key

15. In the menu that appears, find the USB drive with the password utility. Select this drive,
and press Enter
16. Use the arrow keys to select the Save & Exit tab
17. Arrow down to select Save and Reset. Press Enter
18. The AP-3000 will now reboot. While booting, press F11 to enter the boot menu
19. When the boot menu appears, use the arrow keys to select the USB drive. Press Enter
20. The reset utility will start. Select Reset telos user password, and press Enter
21. A confirmation message stating that Password Reset Power off and remove this
password reset USB will appears. Press Enter to continue
22. You will be returned to the menu page. Select Poweroff, and press Enter
23. Remove the USB drive
24. Press the power button on the front of the AP-3000 to boot it back up
25. As the AP-3000 boots, press DEL on the keyboard until the Setup Menu appears
26. Use the arrow keys to select highlight the Boot tab
27. Arrow down to Boot Option 2
28. Press the Enter key
29. In the menu that appears, select disable
30. Use the arrow keys to select the Save & Exit tab
31. Arrow down to select Save and Reset. Press Enter
The password has now been reset to defaults. One next boot, you will be prompted to log in.
the user name is telos. The default password is telos. After entering the password, you will
be prompted to create a new password.
Click here to download the password reset utility

Documento adaptado por Ing. Sebastián Vallejos

Ap 3000 Container Server

Category view
AP-3000 Container Server
1 Sub categories
2 Articles
AP-3000 Password Reset
Published on Mar 20, 2025
Scope This document explains how to reset the CLI user account on an AP-3000. Prerequisites An imaging tool like
Etcher A 2 GB or larger USB flash drive that can be overwritten Physical access to the AP-3000 Keyboard and
Monitor wit…
AP-3000 Quick Start Guide
Published on Dec 16, 2024
AP-3000 Front Panel AP-3000 Rear Panel Thank you for Purchasing the AP-3000 AP-3000 hosts pre-installed
container-delivered Telos Alliance products, providing an alternative to customers who want the benefits of our
software-based…
Help Documents
2 Articles

Documento adaptado por Ing. Sebastián Vallejos

Altus Virtual Mixing Console

Category view
Axia Altus & Altus SE
4 Sub categories
2 Articles
Altus SE Quick Start Guide
Updated on Jun 27, 2025
This quick-start guide is used to connect Altus SE to the network and activate the license. The rest of the
configuration will be completed using the Altus manual. Connections IP Address Configuration Your system is
configured from the fa…
Altus SE System Management Menu
Updated on Aug 20, 2025
Prerequisuites Completed the quick start guide Know the IP Address of one network interface for Altus SE Have
the password for Altus SE Management UI Connecting to Altus SE System Management Menu Altus SE System
Management Menu is only …
Version 2.1 Axia Altus User Manual
1 Sub categories
3 Articles
Version 2.2 Axia Altus User Manual
1 Sub categories
3 Articles
Release Notes
2 Articles
Axia Altus Help Documents
9 Articles

Documento adaptado por Ing. Sebastián Vallejos

Menú de Gestión del Sistema Altus Se

Vista de categoría

Menú de Gestión del Sistema Altus SE
Actualizado el 20 de agosto de 2025

Resumen del artículo
Requisitos previos
Haber completado la guía de inicio rápido
Conocer la dirección IP de una interfaz de red para Altus SE
Tener la contraseña para la interfaz de usuario de gestión de Altus SE

Conexión al Menú de Gestión del Sistema Altus SE
El Menú de Gestión del Sistema Altus SE solo está disponible como una interfaz web. Las siguientes instrucciones son para acceder al menú de gestión del sistema.
1. Abre un navegador web.
2. Escribe la dirección IP asignada a tu Altus SE seguida del puerto 8085. El formato de la barra de URL debe ser Dirección IP:8085. La Dirección IP en cursiva se reemplaza con la dirección IP única asignada a Altus SE.
Las direcciones IP predeterminadas de Altus SE son:
AoIP (LAN 1) – 192.168.2.100:8085
WAN (LAN 2) – 192.168.5.12:8085
Inicia sesión con las credenciales asignadas a Altus SE durante el inicio rápido de Altus SE.

Sistema
Después del inicio de sesión inicial, Altus SE abre la página web del Sistema.

Página del sistema
Esta pantalla es principalmente informativa y tiene dos secciones:

Información de la versión
Aquí se muestra cuál de los dos Bancos de Firmware está actualmente activo y la versión del software que se está ejecutando en ese Banco.

Estado del sistema
Esta sección muestra gráficos que representan la utilización actual de la CPU, memoria, Ethernet y el espacio en disco disponible. Los gráficos se actualizan automáticamente cada dos segundos.

Configuración
La página de Configuración se utiliza para ajustes de red, restablecimiento de fábrica o cierre de sesión en el menú de gestión de Altus SE.

Botones del menú de configuración

Opciones de Configuración de Red
La información actual de la dirección IP es visible en la sección de Configuración de Red de la página de Configuración.
Botón
Reiniciar Sistema
Restablecer Sistema a Valores de Fábrica
Nombre del Host
Cerrar Sesión

Configuración de Livewire y Office
Las opciones de IP del sistema se pueden editar utilizando la pantalla del panel frontal o a través de la interfaz web.
Haga clic en el botón Configure para abrir la pantalla de edición de la interfaz de red.
Escriba los valores de Dirección IP, Máscara de red y Puerta de enlace y haga clic en OK, o haga clic en Cancel para salir de este diálogo sin realizar cambios.
Nota importante: Los cambios en la interfaz de red no tendrán efecto hasta que reinicie el sistema. Por lo tanto, después de cambiar las opciones de IP, notará que la pantalla de Configuración de Red mostrará los cambios entre paréntesis y contará con un nuevo botón de Reboot.

Configuración de Servidores DNS
La sección de DNS lista los servidores DNS actualmente definidos.
Con una configuración de DNS correctamente ajustada, el sistema puede enviar correos electrónicos a los administradores y empleados alertándolos sobre cambios en la red que requieren atención. Por ejemplo, puedes enviar correos electrónicos cuando fuentes o destinos críticos, como cadenas de aire, se vuelven silenciosos. Para hacer esto, el sistema necesita poder resolver los nombres de los servidores de correo con las direcciones IP correctas para enviar el correo. Las entradas de DNS también pueden ser utilizadas al ingresar información del servidor NTP. Habla con tu administrador de red si no estás seguro de qué servidores DNS utilizar.
Haz clic en el botón Configurar Servidor DNS para abrir el cuadro de diálogo Entradas DNS, que te permite agregar, eliminar y reordenar las entradas de los servidores DNS.
Haz clic en Agregar para añadir un nuevo servidor DNS a la lista y en Eliminar para quitar una entrada de servidor DNS.
Para mover un servidor DNS hacia arriba o hacia abajo en la lista de prioridades, selecciona una entrada de servidor DNS y haz clic en los botones << o >>.
Haz clic en Aceptar para guardar tus cambios o en Cancelar para salir del cuadro de diálogo sin realizar cambios.

Copia de Seguridad/Restaurar
La página de Copia de Seguridad/Restaurar presenta una lista de todas las copias de seguridad en el sistema. Si es la primera vez que utilizas esta página, probablemente no habrá copias de seguridad presentes en el sistema.
Para realizar una nueva copia de seguridad o para cargar una copia de seguridad desde tu computadora local de nuevo en el sistema, haz clic en el ícono de más.
Nota Importante: Los cambios en DNS no requieren un reinicio para volverse activos.

Taking Backups
To create a new backup, type a name for the backup, select whether you want logs and/or the
IP address to be included in the backup, and then click Take. Click Cancel to exit the dialog
without making any changes.
The backup will include all configuration files needed to return your system to its current
state.
If logs are included, the backup will also include all system and application logs currently on
the system. The log information can be very useful to Axia support if they are trying to assist
in troubleshooting an issue, and it is likely they will ask you to take a backup, including log
files and send it to them.
If you intend to restore the backup on a different Altus SE, you may not wish to include IP
addresses so the restore process does not overwrite the IP addresses of the other unit.
Important Note: After taking a new backup it is highly recommended that you click on
the link to the backup file and download it to your local computer to store it in a safe
location. Backups that live on Altus SE are not true backups because if the system were
to fail, both the system and the backups could be lost. Downloading a backup to an
external system will also allow you to send the backup to support if necessary.

Uploading Backups
To restore your configuration to a new system, a factory default system, or a system that has
had the desired backup removed from the system, click the plus icon.
Select a System Backup file on your local system, then click Upload.
After the upload is complete, the backup will be available in the Backup/Restore list.
Removing Backups
The minus icon will delete a backup from the system.
Backups are stored in the software Bank. When you move to a new software Bank, you
will not be able to directly access the backups from the previous Bank. However, if the
backup is saved to your local computer, you can easily upload it back into a new Bank if
desired.

Since there is limited space on the storage medium it is recommended to keep only a few
backups on the system at a time.
Restoring Backups
Click the Restore link next to a stored backup. The system will request confirmation that you
really wish to restore the system to that state.
Upload Update
Altus SE has two software banks. This allows a user  to return to an earlier version easily. To
upgrade your system:
Take a backup of your system as explained in the Taking Backups section above; we
always recommend backing up your system before making any major update just to be
safe; the update process generates its own backup as well. The recommended practice is
to have a copy stored on your local computer as well.
Download the new version Altus SE to your local computer
Select the Upload Update from the menu.
This page will display the bank into which the software update will be loaded
Click Browse and select the Altus SE update package
Important Note: The restore function typically happens quickly, but keep in mind that
the system will not be operational during the restore and reboot process.

The File Upload bar will change to the name of the file which you have selected to
upload and a status bar will appear with the Begin button; if the file is not correct for the
type of system you have (for example, you attempt to install VM software to a Fanless
Engine platform) a warning will appear
Click Begin to begin the updating process
A new page will appear with a progress bar that presents stages along with some
additional information regarding what is taking place at that point of the update process;
the update may take several minutes to complete
When the update is complete, the screen below will appear.
To boot into the updated Bank and start using the new software, click the Bank Control
link in the navigation bar
Bank Control
Click Bank Control in the menu to view this page. The Bank Control page displays software
versions in both Banks of Altus SE, and is used to select the active software bank. The

information tables display the software version in each Bank. An asterisk will be present next
to the Bank that is currently executing.
The Bank button can be used to select which Bank will be used on the next reboot. It also
displays the currently selected Bank as the next Bank that will be active at reboot.
After changing the Bank that will be used on the next reboot, a Reboot button will appear on
the page.
Clicking Reboot will reboot into the newly selected Bank.
Configuration File Between Bank Changes
Informational Note: We have occasionally seen some browsers try to cache the state of
this page even though we have requested that page state is not cached. If you reboot
and the executing asterisk does not change, try refreshing the web page. Some
browsers have an extra button you can hold down while refreshing to force the web
page to refresh rather than rely on the cache; for example, with Google Chrome, hold
Shift+CTRL while clicking the refresh icon.

All configuration is transferred between banks during a software update. Altus SE will lose
the IP Address if the banks are changed without a software update. Telos Alliance is working
actively to address this bug. For now if the IP s are lost, follow the directions in the Altus SE
quick start guide to set them again.  
Time
Click on Time in the menu to view this page. The Time configuration page allows you to set
the time zone, define NTP servers, and, if NTP is unavailable, set system time from your local
PC. Setting the time is important as it is used for system logs.
Time Zone Selection
Click the Current Timezone drop-down.
Select the correct timezone for Altus SE
A pop-up to confirm the correct timezone has been selected will appear. Confirm the
timezone is correct, and click OK.
Open the Configuration menu
Click the Reboot button
The time zone system time for Altus SE has been set.  If Altus SE has internet access, the
time will update. If the time does not update Altus SE does not have access to reach the NTP
servers. At this point an NTP server Altus SE has access to can be added, or time can be set
from the PC used to access Altus SE.
NTP Server Management
If Altus SE does not have access to the internet, an additional local NTP server can be added.
Adding NTP Servers
Click the Add button

Fill in the address for the NTP Server Altus SE should connect to
Click the OK button
Reboot Altus SE from the Configuration
Verify Altus SE switches to the proper time
Removing NTP Servers
Click on the NTP Server that needs to be removed
Once highlighted, click the Remove button

NTP Server order
Altus SE can use a list of NTP Servers. The first server (the server at the top of the list) will
be tried first. If a connection cannot be made, Altus SE will try the next server in the list. To
change the order of the servers click the server you want to move up or down the list. Once
highlighted, use the arrow buttons to move the server up or down the list.
Set time from PC
When Altus SE cannot connect to an NTP server, time can be set from the PC used to access
Altus SE. Click the Set time from PC button. Altus SE will use the PC s time for 1 time clock
adjustment. After this adjustment is made Altus SE is keeping time locally.
Password
Click on Password in the menu to view this page. The Password page is used to change the
password to access the Altus SE System Management Menu. To change the password type
the new password into both the Password and Confirm Password fields. Pressing Save will
apply the new password.

SupportLink
Click on SupportLink in the menu to view this page. SupportLink is a tool Telos Alliance can
use to remotely access Altus SE. By default, SupportLink is disabled. SupportLink does
require an internet connection on one Altus SE networks.
Enabling SupportLink
Open the SupportLink drop-down menu
Select the Enabled option
Click the Apply button
SupportLink is now active.
Warning: SupportLink is a remote access tool. Telos Alliance only recommends
activating Supportlink when Telos Alliance request it to be open. It is best practice to
keep SupportLink disabled unless explicitly asked by Telos Alliance to enable
SupportLink.

Logs
Click on Logs menu to view this page. Altus SE has various system logs that Telos Alliance
may request. The directions to view or download these logs are below
Opening a log in the browser
From the list of logs, click the one that needs to be viewed
The log will then open in the browser
Downloading a log
Right click on the log that needs to be download
Select the download file option
Follow prompts to download the log file

Documento adaptado por Ing. Sebastián Vallejos

Guía de Inicio Rápido de Altus Se

Vista de categoría

Guía de inicio rápido de Altus SE
Actualizada el 27 de junio de 2025

Resumen del artículo
Esta guía de inicio rápido se utiliza para conectar el Altus SE a la red y activar la licencia. El resto de la configuración se completará utilizando el manual de Altus.

Conexiones
Configuración de la dirección IP
Su sistema está configurado de fábrica con la dirección IP predeterminada de Livewire y de oficina de la siguiente manera:
Interfaz de red AoIP (LAN1): 192.168.2.100 con una máscara de subred de 255.255.255.0
Interfaz de red WAN (LAN2): 192.168.5.12 con una máscara de subred de 255.255.255.0

Referencia
Notas
A
Puerto DC 12V para fuente de alimentación externa de 120V – 240V, 50/60Hz (incluida)
B
Interfaz de red AoIP (LAN1)
C
Interfaz de red WAN (LAN2)
D
El conector VGA en la parte posterior del Altus SE solo es necesario para configurar los ajustes iniciales de la dirección IP. Alternativamente, puede configurar una red en el mismo rango que las direcciones IP predeterminadas y configurarla a través de la interfaz web.

Estas direcciones IP se pueden cambiar ya sea conectando un monitor y un teclado USB y utilizando el menú intuitivo, o navegando a la dirección IP predeterminada como se describe a continuación.

Asignación de dirección IP para pantalla y teclado
Conecte un monitor al puerto VGA en la parte posterior del Altus SE y un teclado USB a cualquiera de los puertos USB en la parte frontal. Verá un diálogo de menú similar a este:
La navegación del menú utiliza las teclas de flecha y las teclas ENTER y ESC.
Presione ENTER para acceder al menú de configuración.
Utilice las teclas de flecha ARRIBA/ABAJO para resaltar la opción de menú NETWORK, luego presione ENTER.
Menú principal
Utilice las teclas de flecha ARRIBA/ABAJO para resaltar la interfaz de red LIVEWIRE, luego presione ENTER.

Menú de selección de red
Configura los ajustes de IP utilizando las teclas de flecha ARRIBA/ABAJO para incrementar o decrementar los valores y las teclas ENTER o ESC para editar o salir de cada opción; también puedes escribir los números en lugar de usar las teclas de flecha.
Después de configurar los ajustes de IP, NETMASK y GATEWAY, selecciona DONE y luego presiona ENTER.

Menú de configuración de IP
Repite este proceso para la interfaz de Office y la configuración de DNS (DNS puede ser necesario para la configuración de correo electrónico).
Una vez que todas las configuraciones estén completas, navega a Reboot y Apply Settings y presiona ENTER; confirma cualquier solicitud; el sistema se reiniciará con la nueva configuración de red.

Reiniciar y aplicar configuraciones
Ahora puedes continuar configurando el resto de la consola Altus SE.

Configuración de la Dirección IP de Red Alternativa
Conecte la tarjeta de interfaz de red AoIP de Altus SE a un switch de red.
Conecte una computadora al mismo switch y configure la dirección IP de la computadora para que esté dentro del rango 192.168.2.xx, evitando usar 192.168.2.100.
Utilizando un navegador web, acceda a 192.168.2.100:8085.
Inicie sesión utilizando el Nombre de Usuario y la Contraseña predeterminados:
Nombre de Usuario = user
Contraseña = user
Aparecerá un aviso para establecer una contraseña única. Establezca una contraseña única y presione GUARDAR para continuar.
Configuración inicial de la contraseña
Ahora aparecerá un aviso de inicio de sesión. Inicie sesión utilizando la contraseña que acaba de crear. El nombre de usuario sigue siendo user.
Desde el menú, seleccione Configuración.
Utilice los botones Configurar para cambiar la dirección IP, la Máscara de Red y la Puerta de Enlace para las interfaces de red Livewire y de Oficina.

Menú de Configuración
Haga clic en el botón Reiniciar para reiniciar con las nuevas direcciones IP.
Ahora puede continuar con la activación de la licencia y la configuración del resto de la consola Altus SE.

Activación de Licencia
Altus SE se envía con la licencia de software base instalada e inactiva. La activación de la licencia base de Altus SE se realiza en el momento de la instalación, para que la garantía del producto pueda comenzar cuando se instale Altus SE.

Requisitos
Altus SE tiene acceso a internet.

Activación de la Licencia Base
Abra un navegador web y escriba la dirección IP de Altus SE en la barra de URL.
En el menú bajo el encabezado Sistema, haga clic en Licencias.

Advertencia:
La mayoría de las redes AoIP carecen de acceso a internet. La segunda interfaz en Altus SE es una interfaz WAN y puede necesitar estar conectada para activar la licencia.

Se abrirá una nueva pestaña con el menú de licencias. Abre esta nueva pestaña.
Haz clic en el botón verde Activar.
La licencia base ahora estará activa. La página de Licencias se actualizará para mostrar la función base, y la garantía de hardware ha comenzado.
Por favor, continúa a la sección Activación de Funciones Adicionales si se han adquirido funciones complementarias. Si no tienes funciones complementarias, por favor continúa con el manual de Altus SE para la configuración del producto.

Activación de Funciones Adicionales
Una vez que la licencia base esté activa, se pueden agregar funciones adicionales utilizando esta página.
Advertencia: Los bloqueadores de ventanas emergentes a veces impiden que la página de licencias se abra. Si la página de licencias no se abre, verifica si el navegador está bloqueando ventanas emergentes.
Información: Si esta página no se actualiza, Altus SE no puede contactar al servidor de activación. Por favor, contacta a Telos Alliance para obtener asistencia.

Escribe el código de licencia en el cuadro de texto.
Haz clic en el botón Agregar Licencia.
La licencia ahora estará activa. La página de Licencias se actualizará para mostrar que la función está activa.
Altus SE ahora está listo para ser configurado. Continúa con el manual completo del producto para más información.
Información: Si esta página no se actualiza, Altus SE no puede contactar al servidor de activación. Por favor, contacta a Telos Alliance para obtener asistencia.

Documento adaptado por Ing. Sebastián Vallejos